CHOATE 6.4 Complete Cylinder Heads With O-Ring (for 6.4 Powerstroke 2008-2010)
Magnaflux
Iron matrix valve guides honed to size for excellent lubrication and oil retention as well as maximum consistency in guide diameter for longevity. Our Guides are made with higher graphite content which is a lubricating component.
This insures that the life of both valve stem and guide is solid for 100's of thousands of miles, with worry-free service.
Upgraded heavy duty casting, thicker than OE Our Castings are made thicker in problematic areas that have known to fail to cause not only cracks but also leading to fuel contamination in the cooling system. Pressure tested at 50 PSI and 210F and vacuum checked.
Blueprinted to proprietary valve train geometry, to alter valve height and valve recession for maximum reliability and longevity. Our Valve stem heights are altered to remove preload on the lifter and decrease the wear as well as help the lifters live a long life.
Resurface: We incorporate the use of profilometers to make sure that the smoothness and surface finish of the static area meets the Ra of the gasket manufacturer. This is mandatory for proper gasket sealing and keeps the head gasket from failing.
Ra is an arithmetic average of the surface finish. Pressure test: We already test our heads with this process so you can rest assured there is no chance of porosity failures that can be associated with casted parts. Do the job one time the right way!
Hardened seats: 75 percent of heat dissipation occurs through the seating area of the head. This is so important that the valve seat is made of proper metallurgy because it is the conduit to transfer heat from the valve into the cooling system. We only use the highest quality seats to maintain our quality. These hardened seats also fix the problem of cylinder head cracking that is so infamous with the factory integrated seat.
Complete (Add):
- New USA made high-quality valve springs, retainers, locks, valve stem seals, freeze plugs, glow plug sleeves and injector sleeves.
- Valve spring pressure is tested and balanced to ensure consistent spring pressure across all valves
- Valves and Springs are New.
- O-Ring
A receiver groove is machined into the deck surface of the heads and our USA made stainless wire is pressed into the groove- the wire protrudes from the groove applying extra pressure to all layers of the gaskets- sealing combustion pressure in the cylinder. It is reusable should you have the heads off of the engine for any reason in the future.
Our o-ringed heads work with any standard off the shelf head gasket. We do not require any special machining of the block just prep the deck surface ensuring the block is clean dry and flat. We do however prefer the Fel-pro Head gasket.
The O-ring provides a heat sink from the fire ring and conveys that heat obtained into the cooling system.
Vehicles
- 2008-2009 Ford F-250 Super Duty FX4
- 2008-2009 Ford F-350 Super Duty FX4
- 2008-2010 Ford F-250 Super Duty Harley-Davidson Edition
- 2008-2010 Ford F-250 Super Duty King Ranch
- 2008-2010 Ford F-250 Super Duty Lariat
- 2008-2010 Ford F-250 Super Duty XL
- 2008-2010 Ford F-250 Super Duty XLT
- 2008-2010 Ford F-350 Super Duty Harley-Davidson Edition
- 2008-2010 Ford F-350 Super Duty King Ranch
- 2008-2010 Ford F-350 Super Duty Lariat
- 2008-2010 Ford F-350 Super Duty XL
- 2008-2010 Ford F-350 Super Duty XLT
- 2009-2010 Ford F-250 Super Duty Cabela's
- 2009-2010 Ford F-350 Super Duty Cabela's
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.